Gegevens

colorFabb PLA Regrind

colorFabb PLA Maalgoed wordt geproduceerd uit 100% post-filament extrusieafval van colorFabb premium 3D-printfilamenten.

Ons productieteam scheidt nauwgezet filamentafval dat niet aan de specificaties voldoet, om het vervolgens opnieuw te recyclen als colorFabb PLA Regrind.

Elke productierun zal een iets andere kleur hebben, omdat de gerecyclede mix van PLA elke keer dat we een batch colorFabb PLA Regrind produceren, anders zal zijn. Binnen een batch en binnen een spoel is de kleur grotendeels consistent.

colorFabb PLA Regrind vertoont vergelijkbare printeigenschappen als onze andere PLA-kwaliteiten zoals PLA/PHA en PLA Economy.

Pros

100% gerecycled, intern post-extrusieafval

vergelijkbare printeigenschappen als nieuw PLA

beste prijs p/kg PLA

Cons
de kleur zal bij elke batch anders zijn, meestal grijstinten

beperkte beschikbaarheid, slechts enkele productiecampagnes per jaar.

 

Specificatie
Material: 
Colorfabb PLA Regrind
Diameter Tolerance:
± 0.1 mm
Density: 

1,2-1,3 g/cm3

Glass Transition Temperature:
55C
Printadvies

At colorFabb we have a well equipped 3d printing studio with a lot of popular 3d printers. We know our materials will give you excellent results and to help you get these results here are tips and tricks for using colorFabb 3d printing filament.

Advised 3D printing temperature 
195-220℃
Advised 3d print speed
40 - 100 mm/s
Advised Heated bed 
50-60C

Build platform
Our PLA/PHA performs well on both heated and non-heated build platforms. For those users printing on a cold build platform we advise applying masking tape to the build area. The rough surface of the tape will provide enough adhesion for the first layer to stick and print almost without any warping.

Users using heated build platforms have quite a few options these days. The usual suspects are glass and aluminum build plates. For directly printing on glass or aluminum we advice user to apply glue-stick. A very thin layer will be sufficient to keep your print nicely in place. Another method is dissolving wood glue in water, you the consistency of the substance can be quite thin, a bit like milk. By applying just a few drops and smearing this out before you start heating the built plate will create a very thing layer which holds the PLA/PHA down very well. If applying this method, be careful that you don’t get your electronics wet.

Another method that works well with colorFabb PLA/PHA is polyimide tape, or Kapton tape. This tape is available as a very narrow strip or very wide strips which allow you to cover the build plate in one go. When the tape is applied correctly it can last for months.

TIP! Take your time leveling the bed and adjusting the the gap between 3d printer nozzle and build plate. A perfect first layer will is very important, especially for 3d prints with a large bottom layer. Having the nozzle set to close to the build plate will cause a pressure build up and as a result back flow in most hot ends. 

 TIP! PLA/PHA has very minimal warping tendencies, however if your printing parts which take up the maximum of you buildspace you might see some warping. If it’s very important that your part is perfectly flat than we suggest to turn down the fan that is cooling your part. This allows the material to slowly get rid of heat without warping. After a few centimeters you can turn on the cooling if the part needs it.

 *3d printers have lots of different types of hot-end which makes it extremely difficult to give aan temperature advice. We feel our temperature advice holds for most 3d printers, but should be considered as a starting point for you to find the temperatures that work in you setup. Don’t be afraid to go either higher or lower then our advised temperatures if you feel your set-up needs this.

Downloads
Ondersteuning

Heeft u vragen en/of opmerkingen?

Antwoord binnen één werkdag

Contactgegevens

Bericht

Reviews

PLA REGRIND

colorFabb PLA Regrind wordt geproduceerd uit 100% post-filament extrusieafval van colorFabb premium 3D-printingfilamenten.

Ons productieteam scheidt zorgvuldig filamentafval dat buiten specificaties valt, zodat we het opnieuw kunnen recyclen als colorFabb PLA Regrind.

Elke productierun heeft een iets andere kleur omdat de gerecyclede mix van PLA elke keer anders zal zijn wanneer we een batch colorFabb PLA Regrind produceren. Binnen een batch en binnen een spoel is de kleur meestal consistent.

  • Best price per kg
  • 100% recycled PLA
  • Unique color with each batch
Vanaf € 22,74 € 18,79
Op voorraad
Nog %1 beschikbaar
SKU
010037
In Stock: make selection
Back to top